BMT 801EP PRO 1/8 Competition Buggy
The BMT 801EP PRO is a pure competition model.
It is supplied as an assembly kit, complete with bodywork and tires.
Frame:
The frame is in ergal 7075 machined in CNC of new generation, with milling of allergization to improve weight and torsion, it is then treated with Hard anodization.
The front and rear reinforcements are already standard.
All the mechanics of the model are cardan, front and rear with CVA homokinetic, the crowns and pinions of the differentials are made of steel, and everything runs on ball bearings.
The shock absorbers are hydraulic (with oil), are of the new Big Bore 17mm type and are completely in aluminum with a 4.0mm steel stem and adjustable by means of a ring nut to vary the spring hardness.
The shock absorber supports are in ergal 7075 from 4mm thick and have various holes for fixing the shock absorbers in order to change the attitude.
The suspension is fully adjustable, with upper triangle, at the front, with adjustable position, and rear tie rod. All angles like camber, convergence, height etc. they are adjustable.
Suspension arms are equipped with stiffening carbon plates, removable to adapt themselves to the track conditions.
The rear barrels are in ergal, machined from full CNC.
In addition, the front and rear suspensions are equipped with adjustable anti-roll bars for maximum perfomances!
The whole electronic part is protected by an airtight dustproof box with extra battery box to balance the weight of the model.
The motor support is adjustable, and is made entirely from solid, in ergal CNC, the battery holder, has Velcro straps, to fix the batteries in the best possible way.
The lexan body is supplied pre-cut.
The tires and rims are supplied in the kit, they are pin with medium compound that fit most of the land.
Here are some features of this model:
Kit to be installed
Skid plate front in steel
Carbon arms reinforcements
Set of 6 anti-roll bars included
Pre-cut bodywork
Frame in 3mm light ergal
Steel suspension pins
Electronic in airtight box
Adjustable engine support, machined from solid
3 Geared differentials
Battery support case, with flip-up straps in Velcro
Shock absorbers 17mm Big Bore
Front suspension strut in ergal 4mm
Rear suspension strut in ergal 4mm
Frame reinforcements
Anti-splash guards included
Rear and front stabilizer bars
Adjustable steel tie rods
Top plates in carbon
Rear barrels in ergal
Technical data:
Scale: 1/8
Length: 460mm
Width: 306mm
Height: 140mm
Pitch: 322mm
Weight: 3600g
To complete the model car:
Engine and Esc
Radio system
Batteries
The BMT 801EP PRO is a pure competition model.
It is supplied as an assembly kit, complete with bodywork and tires.
Frame:
The frame is in ergal 7075 machined in CNC of new generation, with milling of allergization to improve weight and torsion, it is then treated with Hard anodization.
The front and rear reinforcements are already standard.
All the mechanics of the model are cardan, front and rear with CVA homokinetic, the crowns and pinions of the differentials are made of steel, and everything runs on ball bearings.
The shock absorbers are hydraulic (with oil), are of the new Big Bore 17mm type and are completely in aluminum with a 4.0mm steel stem and adjustable by means of a ring nut to vary the spring hardness.
The shock absorber supports are in ergal 7075 from 4mm thick and have various holes for fixing the shock absorbers in order to change the attitude.
The suspension is fully adjustable, with upper triangle, at the front, with adjustable position, and rear tie rod. All angles like camber, convergence, height etc. they are adjustable.
Suspension arms are equipped with stiffening carbon plates, removable to adapt themselves to the track conditions.
The rear barrels are in ergal, machined from full CNC.
In addition, the front and rear suspensions are equipped with adjustable anti-roll bars for maximum perfomances!
The whole electronic part is protected by an airtight dustproof box with extra battery box to balance the weight of the model.
The motor support is adjustable, and is made entirely from solid, in ergal CNC, the battery holder, has Velcro straps, to fix the batteries in the best possible way.
The lexan body is supplied pre-cut.
The tires and rims are supplied in the kit, they are pin with medium compound that fit most of the land.
Here are some features of this model:
Kit to be installed
Skid plate front in steel
Carbon arms reinforcements
Set of 6 anti-roll bars included
Pre-cut bodywork
Frame in 3mm light ergal
Steel suspension pins
Electronic in airtight box
Adjustable engine support, machined from solid
3 Geared differentials
Battery support case, with flip-up straps in Velcro
Shock absorbers 17mm Big Bore
Front suspension strut in ergal 4mm
Rear suspension strut in ergal 4mm
Frame reinforcements
Anti-splash guards included
Rear and front stabilizer bars
Adjustable steel tie rods
Top plates in carbon
Rear barrels in ergal
Technical data:
Scale: 1/8
Length: 460mm
Width: 306mm
Height: 140mm
Pitch: 322mm
Weight: 3600g
To complete the model car:
Engine and Esc
Radio system
Batteries