BMT 801 PRO 1/8 Competition Nitro Buggy
The BMT 801 PRO is a pure competition model.
It is supplied as an assembly kit, complete with bodywork and tires.
Frame:
The frame is in ergal 7075 machined in CNC of new generation, with milling of allergization to improve weight and torsion, it is then treated with Hard anodization.
The front and rear reinforcements are already standard.
All the mechanics of the model are cardan, front and rear with CVA homokinetic, the crowns and pinions of the differentials are made of steel, and everything runs on ball bearings.
The shock absorbers are hydraulic (with oil), are of the new Big Bore 17mm type and are completely in aluminum with a 4.0mm steel stem and adjustable by means of a ring nut to vary the spring hardness.
The shock absorber supports are in ergal 7075 from 4mm thick and have various holes for fixing the shock absorbers in order to change the attitude.
The brakes, the tablets are in Real Ferodo, with the same process of realization of the true cars 1/1. They are double disc, one acting on the front axle and one acting on the rear axle in order to vary the braking power on the two axles.
The suspension is fully adjustable, with upper triangle, at the front, with adjustable position, and rear tie rod. All angles like camber, convergence, height etc. they are adjustable.
Suspension arms are equipped with stiffening carbon plates, removable to adapt themselves to the track conditions.
The rear barrels are in ergal, machined from full CNC.
In addition, the front and rear suspensions are equipped with adjustable anti-roll bars for maximum perfomances!
The whole electronic part is protected by an airtight dustproof box with extra battery box to balance the weight of the model.
The lexan body is supplied pre-cut.
The tires and rims are supplied in the kit, they are pin with medium compound that fit most of the land.
Motor Accessories:
Included in the assembly kit, the 3-link clutch, and the two-stage air filter.
Here are some features of this model:
Kit to be installed
Skid plate front in steel
Carbon arms reinforcements
Set of 6 anti-roll bars included
Pre-cut bodywork
3mm light ergal frame
Suspension pins in steel
Electronic in airtight box
Lightweight tank with filter
Double disc brakes with racing pads
3 Differentials with gears
Filter double-stage air
Shock absorbers 17mm Big Bore
Front suspension strut in 4mm ergal
Rear suspension strut in 4mm ergal
Frame reinforcements
Anti-splash guards included
Rear and front stabilizer bars
Adjustable steel tie rods
Top plates in carbon
Rear barrels in ergal
Racing clutch
Technical data:
Scale: 1/8
Length: 460mm
Width: 306mm
Height: 140mm
Pitch: 322mm
Weight: 3600g
To complete the model car:
Engine and exhaust system
Radio system
Rx battery
The BMT 801 PRO is a pure competition model.
It is supplied as an assembly kit, complete with bodywork and tires.
Frame:
The frame is in ergal 7075 machined in CNC of new generation, with milling of allergization to improve weight and torsion, it is then treated with Hard anodization.
The front and rear reinforcements are already standard.
All the mechanics of the model are cardan, front and rear with CVA homokinetic, the crowns and pinions of the differentials are made of steel, and everything runs on ball bearings.
The shock absorbers are hydraulic (with oil), are of the new Big Bore 17mm type and are completely in aluminum with a 4.0mm steel stem and adjustable by means of a ring nut to vary the spring hardness.
The shock absorber supports are in ergal 7075 from 4mm thick and have various holes for fixing the shock absorbers in order to change the attitude.
The brakes, the tablets are in Real Ferodo, with the same process of realization of the true cars 1/1. They are double disc, one acting on the front axle and one acting on the rear axle in order to vary the braking power on the two axles.
The suspension is fully adjustable, with upper triangle, at the front, with adjustable position, and rear tie rod. All angles like camber, convergence, height etc. they are adjustable.
Suspension arms are equipped with stiffening carbon plates, removable to adapt themselves to the track conditions.
The rear barrels are in ergal, machined from full CNC.
In addition, the front and rear suspensions are equipped with adjustable anti-roll bars for maximum perfomances!
The whole electronic part is protected by an airtight dustproof box with extra battery box to balance the weight of the model.
The lexan body is supplied pre-cut.
The tires and rims are supplied in the kit, they are pin with medium compound that fit most of the land.
Motor Accessories:
Included in the assembly kit, the 3-link clutch, and the two-stage air filter.
Here are some features of this model:
Kit to be installed
Skid plate front in steel
Carbon arms reinforcements
Set of 6 anti-roll bars included
Pre-cut bodywork
3mm light ergal frame
Suspension pins in steel
Electronic in airtight box
Lightweight tank with filter
Double disc brakes with racing pads
3 Differentials with gears
Filter double-stage air
Shock absorbers 17mm Big Bore
Front suspension strut in 4mm ergal
Rear suspension strut in 4mm ergal
Frame reinforcements
Anti-splash guards included
Rear and front stabilizer bars
Adjustable steel tie rods
Top plates in carbon
Rear barrels in ergal
Racing clutch
Technical data:
Scale: 1/8
Length: 460mm
Width: 306mm
Height: 140mm
Pitch: 322mm
Weight: 3600g
To complete the model car:
Engine and exhaust system
Radio system
Rx battery